Dear Vernon,
Like yourself, I too would also approach the use of B72 on painted and/or varnished surfaces with some caution as acetone can sometimes soften these layers. I'm not someone who has had to carry out labeling personally, but I suspect that some of your colleagues here who have been working with the Lascaux adhesives have been given this advice with similar solvent sensitivity concerns in mind. Lascaux 498 is a synthetic polymer but one that has been modified so that it in a water based dispersion. Diana Welsh does a great job of describing it, it will be white in appearance in the jar (just like Elmers) but will dry to a clear film. Lascaux 498 can be thinned with water but once dry it cannot be removed with water. If the surface you are applying it to is not too porous it can often be peeled or rolled off once dry just like you peel dried Elmers off your hands. While it is considered an adhesive it can create a topcoat. That coating will be softer and flexible than B72. While B72 may smear your ink because of the solvents I would imagine that if Lascaux is applied too wet it could swell your paper label. Taken straight from the bottle I doubt that would be a problem but again like B72 as that bottle sits after it is opened it will start to thicken and you may have to dilute it slightly to make it workable.
I am on the advisory committee for C2CCare and we have been watching this thread with interest and are hoping to develop some programing around this topic, so stay tuned!
Thanks for bringing ever greater insight to my understanding of the challenges you face!
Best,
Heather
------------------------------
Heather Galloway
Conservator, Fellow
Galloway Art Conservation
1305 W 80th St. Suite #225
Cleveland, OH 44102
------------------------------
Original Message:
Sent: 09-17-2020 13:54
From: Vernon Weckbacher
Subject: B72 labeling problems
We have used B-67 in naphtha for labeling items where the surface might be damaged by acetone, particularly painted surfaces and finished wood. If better alternatives have been developed, I would be interested in hearing about them. As always, when in doubt, we tag items or use some other inert or non-intrusive means of marking.
Vernon G. Weckbacher
Archivist/Curator
Mission Historical Museum
900 Doherty
Mission, TX, 78572
956-580-8646
Original Message:
Sent: 9/17/2020 11:48:00 AM
From: Heather Galloway
Subject: RE: B72 labeling problems
I'm curious Vernon what factors you are weighing when you decide to use B67 vs B72? Is it the solvent, the workability, the surface of the object you are applying it to? As a paintings conservator my experience of B67 used as a varnish is one that is checkered. In general B72 has better aging characteristics. B67 can crosslink and while you can find aged B67 coatings that remain soluble I also have experienced B67 coatings that are tough to remove. I am wondering if there is a better choice for you when you do not want to use B72 but having a better idea of your concerns are would help. I should also add that B67, like B72, has been promoted by the conservation community and is probably still in use, it is only with more time that we have begun to experience some of its less desirable characteristics.
Best,
Heather
------------------------------
Heather Galloway
Conservator, Fellow
Galloway Art Conservation
1305 W 80th St. Suite #225
Cleveland, OH 44102
------------------------------
Original Message:
Sent: 09-17-2020 09:01
From: Vernon Weckbacher
Subject: B72 labeling problems
We also use paper labels with B-72 in acetone (B-67 in naphtha for some items). We've had a few instances of bubbling, but not often enough to be a problem. It's important to not over-work the coating, which can result in a lumpy appearance due to the acetone's rapid evaporation. Setting the paper label in place quickly and soaking an ample topcoat into the paper helps keep the label from coming off after it's dry.
Vernon G. Weckbacher
Archivist/Curator
Mission Historical Museum
900 Doherty
Mission, TX, 78572
956-580-8646
Original Message:
Sent: 9/16/2020 10:21:00 AM
From: Victoria Kablys
Subject: RE: B72 labeling problems
Posted on behalf of:
Katherine Ridgway
State Archaeological Conservator
Virginia Department of Historic Resources
"I've attached an article from the JAIC on labeling artifacts in case that helps. If they have been using the same lacquer and pens for years, there's been no change in their process, and no drastic environmental changes (extra high humidity), it makes me think that there has been some change in the formulation of the lacquer or the ink or both. Maybe a new solvent or some other change? It might be worth contacting the manufacturer to see if they have any information on updated formulas that they are using. I found that it took so long for the various layers and ink to dry that it ended up not being worth the wait. Now I put a printed label (archival paper) between layers of B-72 and it makes the process much faster. It also helps with legibility since my handwriting isn't the greatest. If there is bubbling that affects the legibility of the label, I use a brush with some acetone to pop the bubbles (not too much) and I can usually see immediate improvement. Archival pens on archival paper should also work. I hope this helps and let me know if you have any other questions!"
------------------------------
Victoria Kablys
Conservator
Royal Saskatchewan Museum
Regina SK
(306) 787-2667
Original Message:
Sent: 09-14-2020 12:09
From: Cindy Opitz
Subject: B72 labeling problems
I had similar problems using Paraloid B72 as a topcoat, but now I get better results using the Faber-Castell Pitt Artist Pen for marking and Golden Self-leveling (acrylic) Gel as a topcoat. The gel is cloudy when wet but dries to a clear, level finish, with no bubbling.
------------------------------
Cindy Opitz
Director of Research Collections
Museum of Natural History and Old Capitol Museum
The University of Iowa
Iowa City IA
319-335-0481
Original Message:
Sent: 09-11-2020 19:44
From: Laura Belani
Subject: B72 labeling problems
I am also interested in this information. I use Paraloid B-72 as a barrier and top coat and label using archival ink and pen nibs. I have only had this problem if I apply the top coat to quickly to the number after labeling. And, what you described always occurs when I use a Pigma Micron pen for labeling. I've given up on those pens as it never turns out looking clean or clear.
------------------------------
Laura Belani
Collection Manager
Bowers Museum
Santa Ana CA
(714) 567-3652